ReflexCES Sargon Stratix® 10 GX FMC+ Development Kit
High performance and flexible, new lower price!
The Sargon Stratix-10 GX FPGA Development Kit includes a full height PCI-express form-factor board, featuring the Intel® Stratix® 10 GX 2800 KLE FPGA which operates in a Host PC via the PCIe Gen3 x16 interface or in stand-alone mode with the included power supply. This full-featured development kit’s price has been reduced by $1,000 and includes all the software needed to start developing your design.
Main features:
- Intel® Stratix® 10 GX 2800 KLEs
- PCI-express Gen3 x16
- 8Gbytes of on-board x72-bit DDR4 memory and two x72-bit DDR4 RDIMM sockets
- 1x FMC+ (VITA57.4) with 24 XCVR, 20 XCVR up to 28Gb/s, 4 XCVR up to 17.4Gb/s, 2x Hard IP 100G transceivers blocks capable
- GPIO extension connector : 9 LVDS usable as 18 LVCMOS
- XCVR extension connector : 10 XCVR, 8 LVDS, Clock In&Out
- Board Management Controller (BMC) for monitoring, NOR Flash and Clock Programming
- Mini-SAS, Firefly, SDI and Gigabit Ethernet interfaces
- On-board USB Blaster for FPGA programming and debug
- Intel Quartus Prime Pro DKE 1-year license included
Target Applications:
- High Performance Data Center and Cloud Computing
- IP & ASIC Prototyping
- Pre-tapeout functional ASIC verification
- Early/Pre-ASIC software development
Tech spec
FPGA
- Intel® Stratix® 10 GX 2800 KLEs
- PCIe Gen3 x16
Board Programming
- Max10 USB Blaster on board, UART over USB interface
- 1x Nor Flash 1GB quad SPI FPGA AS configuration
- 1x Nor Flash 1GB for configuration mode ST8
- Board Management Controller (BMC) for monitoring, NOR Flash and clock programming
Memory
- 2x banks DDR4 vertical RDIMM, 16GBytes each, x72bit, up to 2400MT/s. The RDIMMs are not provided but can be purchased separately
- 1x bank DDR4 soldered on PCB, bus x72, 8GBytes up to 2400MT/s
Communication & Interfaces
- 2x FireFly™ Samtec quad connector (28Gb/s each XCVR) - 1 FireFly™ connected to 100G IP
- 1x FMC+ (VITA57.4) with 24 XCVR, 20 XCVR up to 28Gb/s, 4 XCVR up to 17.4Gb/s, 2x Hard IP 100G transceivers blocks capable
- MiniSAS quad connector (1 HD SAS, 4 SATA HDD, NVMe interface capable)
- GPIO extension connector : 9 LVDS usable as 18 LVCMOS
- XCVR extension connector : 10 XCVR, 8 LVDS, Clock In&Out
- 1x Ethernet SGMII interface (to FPGA), Marvel PHY 88E11
Clock Circuitry
- Programmable PLL oscillator (Si5341), output clocks frequency between 0.0001 MHz to 750 MHz
- High precision oscillator, clock accuracy 20MHz- 0.01ppm for Precision Time Protocol (PTP) IEEE 1588
- One coax connector for PPS (pulse per second)
Board Size
- Length : 254 mm (10 inches)
- Height : 111.15 mm (4.38 inches) / Standard Height PCIe
- Dual slot PCIe
Power
- Max 240W including FMC board, delivered with active heat-sink
Operating Range
- 0°C to 40°C
Storage Temp Range
- 0°C to 70°C