2012-08-01

Arria V GX Starter Kit

The Altera® Arria® V GX Starter Kit provides a complete design environment that includes all the hardware and software you need to develop cost-sensitive FPGA applications immediately. The development kit is RoHS compliant. The development kit features the following:

 

  • Arria V GX FPGA—360KLE, F1517 package, 24X6.6G XCVRs, C4 speed grade
  • One I/O expansion slot—one high-speed mezzanine card (HSMC) connector
  • 16 MB of SDRAM memory
  • High-definition multimedia interface (HDMI) and serial digital interface (SDI) connections
  • SMAs
2012-08-01-ArriaVGX-1.gif

Ordering Information

Table 1. Arria V GX Starter Kit Ordering Code and Pricing Information
Ordering CodePriceOrdering Information
DK-START-5AGXB3NES$850

The Arria V GX Starter Kit features a 5AGXB3 Engineering Sample (ES) device and a 1-year license for the Quartus® II design software.

  Contact your local Altera distributor to place your order.

 

Starter Kit Contents

  • The Arria V GX Starter Kit features the following:
    • Arria V GX FPGA development board (see Figure 1)
    • FPGA: Arria V GX 5AGXFB3H4F35C4NES
    • System controller: MAX® V 5M2210ZF256C4N
      • Power monitor GUI
      • Single analog-to-digital converter (ADC), eight channels
      • Non-isolated power rail
      • Fast passive parallel (FPP) x16 mode through parallel flash loader (PFL)
      • Control and status registers
    • Embedded USB-BlasterTM II: MAX II EPM570GM100C4N
    • HDMI 1.3 TX
      • x4 XCVR, 3.4 Gbps (max by spec) and 340 MHz TX clock (by spec)
      • HDMI TX connector
      • TI HDMI level shifter SN75DP130
      • Level shift XCVR PCML 1.5V <-> TMDS level
      • DDC and HPD <-> HDMI compliant level
      • Data channel up to 5.4 Gbps; HDMI 1.3 only needs a maximum of 3.4 Gbps
      • Clock channel up to 340 MHz; enough to support 3.4 Gbps data rate
      • HDMI specification: clock period = 10x of UI
      • Requires 100 MHz clock input at CLKIN to generate the TX clk and core logic
    • SDI 3G
      • x1 XCVR TX/RX loopback
      • x2 SMB connectors and cable (cable not included in kit)
      • Up to 2.97 Gbps
      • Uses National Semiconductor driver/receiver LMH0384SQ/LMH0303SQx
      • Requires 148.5 MHz and 148.35 MHz at XCVR refclk to support US and EU standard respectively
      • Use VCXO to fine tune and lock to the recovered CDR frequency
      • Requires 125 MHz CLKIN for core logic
    • HSMC
      • x8 XCVR up to 6.375 Gbps
      • Not complied to PCI Express® (PCIe®) HIP pin assignment
      • x4 CMOS
      • x17 differential using dedicated TX/RX channel
      • x2 low-voltage differential signalling (LVDS) clock in
      • x2 differential clock out
      • I2C
      • JTAG
      • Minimum current support
      • 2A @ 3.3V
      • 1A @ 12V
      • Dedicated clock domain from Si 5338 clock generator for xcvr refclk
      • HSMC loopback with BTS GUI
    • SMA
      • 7x XCVR TX/RX channel
      • 1x LVDS clock input
    • Dedicated clock domain from Si 5338 clock generator for xcvr refclk
    • DDR3 SDRAM x32
      • Micron MT41J64M16JT-15E DDR3 SDRAM 8MX16X8
      • Two devices: 2 x16 width = x32
      • BTS DDR3 SDRAM GUI using Uniphy and high performance (HP) controller II
    • SSRAM
      • 1024k x18, 18 Mb ISSI IS61VPS102418A
      • Shared address or data with flash
    • User IO
      • LCD character
      • x4 DIP switch
      • x3 PB
      • x4 LED
    • Configuration
      • FPP x16 mode
      • Dual flash 512Mbit Numonyx PC28F512P30BF (52 MHz FMAX)
    • JTAG header
    • Embedded USB Blaster II
      • Cypress Microcontroller CY7C68013A as USB PHY 2.0
      • MAX II
      • Ethernet
      • 10/100/1000 Base-T
      • RJ-45 connector, on-board LED for link status
      • Marvell Ethernet PHY 88E1111
      • Requires 100 MHz and 125 MHz clock from CLKIN

 

Figure 1: Arria V GX Starter Board with a 5AGXB3ES FPGA Device

Figure 2: Arria V GX Starter Board Block Diagram

 

Related Links